Products

Silica Aerogel Product Portfolio

Filter by material form and engineering use. Each product has a dedicated SEO-ready technical profile for Google and AI discovery.

CW-AP

Hydrophobic Silica Aerogel Powder and Particles

Nanoporous SiO2 aerogel raw material for coatings, composite fillers and functional modification systems.

400-800 m2/g specific surface area
90-95% porosity
20-50 nm pore size
Hydrophobic surface

Waterborne industrial coatingsThermal coating formulasComposite fillers

Designed against JC/T 2518-2019 requirements for hydrophobic silica aerogel powder.

View technical profile

CW-AT-H / CW-AT-L

Aerogel Blanket for Industrial Insulation

Flexible aerogel blankets for medium-high temperature insulation, cryogenic service, tanks, pipelines and constrained spaces.

0.020 W/(m·K) at 25C
Up to 650C service for CW-AT-H
-200C to 125C for CW-AT-L
Hydrophobicity up to 99.9%

Steam pipelinesProcess equipmentLNG logisticsCold chain

Product quality aligned with GB/T 34336-2017 nanoporous aerogel composite insulation products.

View technical profile

CW-AC-01/02

Building Aerogel Thermal Insulation Coating

Waterborne thin-layer aerogel insulation coating used with primer and topcoat for exterior walls, roofs, retrofits and industrial buildings.

0.040 W/(m·K) tested thermal conductivity
0.26 m2·K/W added thermal resistance
35 g/L VOC
0.5 g/mL density

Exterior wallsRoof retrofitFactory buildingsEnergy-saving renovation

Shanghai Jianke XT226-250016 report: compliant with GB/T 25261-2018 and DG/TJ08-2200-2024.

View technical profile

CW-AC-14/15/16

Industrial Aerogel Insulation Coating

Sprayable or trowel-applied aerogel insulation coating for equipment, valves, elbows and complex industrial surfaces up to 180C.

-40C to 180C service range
≤0.04 W/(m·K) thermal conductivity
≤1.5 mm single wet film
Three-layer protection system

Hot equipmentPipe elbowsValves and flangesBurn protection

Installation guidance defines primer, aerogel mid-coat, topcoat, dew-point control and curing windows.

View technical profile

CW-FTHL

Aerogel Fireproof Coating for Steel Structures

Waterborne ultra-thin intumescent coating that forms an expanded char layer under fire while aerogel slows heat transfer to steel.

66±3% solids
1.30 g/cm3 density
2 h surface dry
28-day full cure

Steel factoriesPetrochemical framesPower facilitiesCommercial steel

Designed for GB14907-2018 fireproof coating requirements. Fire-resistance ratings must be matched to project test reports.

View technical profile

Indoor / Outdoor Systems

Non-Intumescent Fire Protection Coating

Thick-film fire protection coating systems for steel structures requiring higher dry film thickness and defined fire-resistance duration.

24 mm / 2.5 h reference system
100% solids
4 h surface dry
28-day full cure

Steel fire protectionOutdoor exposureIndustrial structures

Indoor dry density ≤500 kg/m3. Outdoor dry density ≤650 kg/m3.

View technical profile

CW-WP-01

Silicon-Based Penetrating Water Repellent

Low-viscosity penetrating water repellent that forms nanoscale hydrophobic interfaces inside porous concrete, masonry and stone substrates.

0.93 g/cm3 density
pH 4-7
8-14% solids
250 ml/m2 recommended dosage

Concrete structuresStone protectionMortar and gypsumRepair and retrofit

2024W06363 report: 19% water absorption ratio, 0 mm permeability and no staining under multiple aging conditions.

View technical profile

CW-AJ

Aerogel Paste and Sealant Compound

Flexible aerogel composite paste for thin-layer encapsulation, sealing, wear resistance and local thermal insulation.

0.041 W/(m·K) thermal conductivity
>1 MPa adhesion
Class B combustion behavior
Trowel or roller applied

Aerogel felt surface treatmentSubstrate coatingEncapsulationVibration and heat isolation

90C drying for 24 hours is recommended when higher adhesion is required.

View technical profile

Ask an engineer to match the right product